View LH52256C_130650.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LH52256C/CH
FEATURES * 32,768 x 8 bit organization * Access time: 70 ns (MAX.) * Supply current: Operating: 45 mA (MAX.) 10 mA (MAX.) (tRC, tWC = 1 s) Standby: 40 A (MAX.) * Data retention current: 1.0 A (MAX.) (VCCDR = 3 V, TA = 25C) * Wide operating voltage range: 4.5 V 5.5 V * Operating temperature: Commerical temperature 0C to +70C Industrial temperature -40 to +85C * Fully-static operation * Three-state outputs * Not designed or rated as radiation hardened * Package: 28-pin, 600-mil DIP 28-pin, 450-mil SOP 28-pin, 300-mil SK-DIP 28-pin, 8 x 3 mm2 TSOP (Type I) * N-type bulk silicon DESCRIPTION
The LH52256C is a Static RAM organized as 32,768 x 8 bits which provides low-power standby mode. It is fabricated using silicon-gate CMOS process technology.
CMOS 256K (32K x 8) Static RAM
PIN CONNECTIONS
28-PIN DIP 28-PIN SK-DIP 28-PIN SOP A14 A12 A7 A6 A5 A4 A3 A2 A1 A0 I/O1 I/O2 I/O3 GND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 VCC WE A13 A8 A9 A11 OE A10 CE I/O8 I/O7 I/O6 I/O5 I/O4
52256C-1
TOP VIEW
Figure 1. Pin Connections
28-PIN TSOP (Type I)
OE A11 A9 A8 A13 WE VCC A14 A12 A7 A6 A5 A4 A3
1 2 3 4 5 6 7 8 9 10 11 12 13 14
28 27 26 25 24 23 22 21 20 19 18 17 16 15
A10 CE I/O8 I/O7 I/O6 I/O5 I/O4 GND I/O3 I/O2 I/O1 A0 A1 A2
NOTE: Reverse bend available on request.
52256C-8
Figure 2. TSOP (Type I) Pin Connections
1
LH52256C/CH
CMOS 256K (32K x 8) Static RAM
A8 25 A14 1 A13 26 A12 2 A7 3 ROW DECORDER A6 4 A5 5 A4 6 11 I/O1 12 I/O2 COLUMN I/O CIRCUIT COLUMN DECODER 8 OUTPUT BUFFERS 13 I/O3 15 I/O4 16 I/O5 17 I/O6 18 I/O7 19 I/O8 A3 7 MEMORY ARRAY (512 x 512) 28 VCC 14 GND
8
INPUT DATA CONTROL WE 27
OE 22 CE 20 10 9 8 21 24 23 A0 A1 A2 A10 A9 A11
52256C-2
Figure 3. LH52256C Block Diagram
PIN DESCRIPTION
SIGNAL PIN NAME SIGNAL PIN NAME
A0 - A14 CE WE OE
Address inputs Chip enable Write enable Output enable
I/O1 - I/O8 VCC GND
Data inputs and outputs Power supply Ground
2
CMOS 256K (32K x 8) Static RAM
LH52256C/CH
TRUTH TABLE
CE WE OE MODE I/O1 - I/O8 SUPPLY CURRENT NOTE
H L L L
X H H L
X L H X
Standby Read Output disable Write
High impedance Data output High impedance Data input
Standby (ISB ) Active (ICC) Active (ICC) Active (ICC)
1 1 1 1
NOTE: 1. X = Don't care, L = Low, H = High
ABSOLUTE MAXIMUM RATINGS
PARAMETER SYMBOL RATING UNIT NOTE
Supply voltage Input voltage Operating temperature Storage temperature
VCC VIN TOPR TSTG
-0.5 to +7.0 -0.5 to VCC + 0.5 0 to +70 -65 to +150
V V C C
1 1, 2

NOTES: 1. The maximum applicable voltage on any pin with respect to GND. 2. Undershoot of -3.0 V is allowed width of pulse below 50 ns.
RECOMMENDED DC OPERATING CONDITIONS (TA = 0C to +70C)
PARAMETER SYMBOL MIN. TYP. MAX. UNIT NOTE
Supply voltage Input voltage
VCC VIH VIL
4.5 2.2 -0.5
5.0
5.5 VCC + 0.5 0.8
V V V

1

NOTE: 1. Undershoot of -3.0 V is allowed width of pulse below 50 ns.
3
LH52256C/CH
CMOS 256K (32K x 8) Static RAM
DC ELECTRICAL CHARACTERISTICS (TA = 0C to +70C, VCC = 4.5 V to 5.5 V)
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNIT
Input leakage current Output leakage current Operating supply current
ILI ILO ICC ICC1
VIN = 0 V to VCC CE = VIH or OE = VIH VI/O = 0 V to VCC Minimum cycle, VIN = VIL or VIH II/O = 0 mA, CE = VIL tRC, tWC = 1 s, VIN = VIL or VIH, II/O = 0 mA, CE = VIL CE VCC - 0.2 V CE = VIH IOL = 2.1 mA IOH = -1.0 mA
-1.0 -1.0

25
1.0 1.0 45.0
A A

2.4
mA
0.6
10.0 40.0 3.0 0.4 A mA V
Standby current
ISB ISB1

Output voltage
VOL VOH
NOTE: Typical values at VCC = 5.0 V, TA = 25C
AC ELECTRICAL CHARACTERISTICS AC Test Conditions
PARAMETER MODE NOTE
Input pulse level Input rise and fall time Input and output timing Ref. level Output load
NOTE: 1. Including scope and jig capacitance.
0.6 V to 2.4 V 10 ns 1.5 V 1 TTL + CL (100 pF)

1
READ CYCLE (TA = 0C to +70C, VCC = 4.5 V to 5.5 V)
PARAMETER SYMBOL MIN. MAX. UNIT NOTE
Read cycle time Address access time CE access time Output enable to output valid Output hold from address change CE Low to output active OE Low to output active CE High to output in High impedance OE High to output in High impedance
tRC tAA tACE tOE tOH tLZ tOLZ tHZ tOHZ
70
70 70 35
ns ns ns ns ns ns ns ns ns

1 1 1 1

10 10 5 0 0

30 30
NOTES: 1. Active output to high-impedance and high-impedance to output active tests specified for a 200 mV transition from steady state levels into the test load.
4
CMOS 256K (32K x 8) Static RAM
LH52256C/CH
WRITE CYCLE (TA = 0C to +70C, VCC = 4.5 V to 5.5 V)
PARAMETER SYMBOL MIN. MAX. UNIT NOTE
Write cycle time CE Low to end of write Address valid to end of write Address setup time Write pulse width Write recovery time Input data setup time Input data hold time WE High to output active WE Low to output in High impedance OE High to output in High impedance
tWC tCW tAW tAS tWP tWR tDW tDH tOW tWZ tOHZ
70 45 45 0 35 0 30 0 5 0 0

30 30
ns ns ns ns ns ns ns ns ns ns ns

1 1 1
NOTE: 1. Active output to high-impedance and high-impedance to output active tests specified for a 200 mV transition from steady state levels into the test load.
CAPACITANCE (TA = 25C, f = 1MHz)
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNIT NOTE
Input capacitance I/O capacitance
CIN CI/O
VIN = 0 V VI/O = 0 V

7 10
pF pF
1 1
NOTE: 1. This parameter is sampled and not production tested.
DATA RETENTION CHARACTERISTICS (TA = 0C to +70C)
PARAMETER SYMBOL CONDITIONS MIN. TYP. MAX. UNIT NOTE
Data retention supply voltage
VCCDR
CE VCCDR - 0.2 V VCCDR = 3.0 V TA = 25C TA = 40C CE VCCDR - 0.2 V
2.0
0.3
5.5 1.0 3.0 15
V

Data retention supply current
ICCDR
A
Chip enable setup time Chip enable hold time
NOTE: 1. t RC = Read cycle time. 2. Typical values at TA = 25C
tCDR tR

0 tRC

ns ns
1
5
LH52256C/CH
CMOS 256K (32K x 8) Static RAM
tRC
ADDRESS tAA tACE
CE tLZ tOE tHZ
OE tOLZ tOHZ tOH
DOUT NOTE: WE is HIGH for Read Cycle.
DATA VALID
52256C-3
Figure 4. Read Cycle
6
CMOS 256K (32K x 8) Static RAM
LH52256C/CH
tWC
ADDRESS
OE tAW tCW
(NOTE 2)
tWR
(NOTE 4)
CE tAS
(NOTE 3)
tWP
(NOTE 1)
tWR
(NOTE 4)
WE tOHZ
(NOTE 6)
DOUT tDW
(NOTE 5)
tDH
DIN NOTES: 1. A write occurs during the overlap of a LOW CE, and a LOW WE. A write begins at the latest transition among CE going LOW, and WE going LOW. A write ends at the earliest transition among CE going HIGH, and WE going HIGH. tWP is measured from the beginning of write to the end of write. 2. tCW is measured from the later of CE going LOW to the end of write. 3. tAS is measured from the address valid to the beginning of write. 4. tWR is measured from the end of write to the address change. 5. During this period, I/O pins are in the output state, therefore the input signals of opposite phase to the outputs must not be applied. 6. If CE goes LOW simultaneously with WE going LOW or after WE going LOW, the outputs remain in high impedance state. 7. If CE goes HIGH simulaneously with WE going HIGH or before WE going HIGH, the outputs remain in high impedance state.
DATA VALID
52256C-4
Figure 5. Write Cycle (OE Controlled)
7
LH52256C/CH
CMOS 256K (32K x 8) Static RAM
tWC
ADDRESS tAW tCW
(NOTE 2)
tWR
(NOTE 4)
CE tAS
(NOTE 3)
tWP
(NOTE 1)
tWR
(NOTE 4)
WE tWZ tOW
(NOTE 7)
(NOTE 6)
DOUT tDW DIN
(NOTE 5)
tDH DATA VALID
NOTES: 1. A write occurs during the overlap of a LOW CE, and a LOW WE. A write begins at the latest transition among CE going LOW, and WE going LOW. A write ends at the earliest transition among CE going HIGH, and WE going HIGH. tWP is measured from the beginning of write to the end of write. 2. tCW is measured from the later of CE going LOW to the end of write. 3. tAS is measured from the address valid to the beginning of write. 4. tWR is measured from the end of write to the address change. 5. During this period, I/O pins are in the output state, therefore the input signals of opposite phase to the outputs must not be applied. 6. If CE goes LOW simultaneously with WE going LOW or after WE going LOW, the outputs remain in high impedance state. 7. If CE goes HIGH simulaneously with WE going HIGH or before WE going HIGH, the outputs remain in high impedance state.
52256C-5
Figure 6. Write Cycle (OE Low Fixed)
CE CONTROL
DATA RETENTION MODE VCC 4.5 V 2.2 V VCCDR CE VCCDR - 0.2 V CE 0V
52256C-6
tCDR
tR
Data Retention Timing Chart CE Controlled
8
CMOS 256K (32K x 8) Static RAM
LH52256C/CH
PACKAGE DIAGRAMS
28DIP (DIP028-P-0600)
28 15
DETAIL
13.45 [0.530] 12.95 [0.510]
1 36.30 [1.429] 35.70 [1.406]
14
0 TO 15 0.30 [0.012] 0.20 [0.008] 15.24 [0.600] TYP.
4.50 [0.177] 4.00 [0.157] 5.20 [0.205] 5.00 [0.197] 3.50 [0.138] 3.00 [0.118] 2.54 [0.100] TYP. 0.60 [0.024] 0.40 [0.016] MAXIMUM LIMIT MINIMUM LIMIT 0.51 [0.020] MIN.
DIMENSIONS IN MM [INCHES]
28DIP-2
28SOP (SOP028-P-0450)
1.27 [0.050] TYP. 1.70 [0.067] 15 8.80 [0.346] 8.40 [0.331] 12.40 [0.488] 11.60 [0.457]
0.50 [0.020] 0.30 [0.012]
28
10.60 [0.417]
1 18.20 [0.717] 17.80 [0.701]
14 1.70 [0.067] 0.20 [0.008] 0.10 [0.004] 0.15 [0.006] 1.025 [0.040] 2.40 [0.094] 2.00 [0.079] 0.20 [0.008] 0.00 [0.000] 1.025 [0.040]
DIMENSIONS IN MM [INCHES]
MAXIMUM LIMIT MINIMUM LIMIT
28SOP
9
LH52256C/CH
CMOS 256K (32K x 8) Static RAM
28SDIP (SDIP28-P-400)
28 15
DETAIL
8.80 [0.346] 8.40 [0.331] 0 TO 15 0.30 [0.012] 0.20 [0.008] 4.05 [0.159] 3.65 [0.144] 4.60 [0.181] 4.20 [0.205] 3.50 [0.138] 3.00 [0.118] 1.78 [0.070] TYP. 0.56 [0.022] 0.36 [0.014] MAXIMUM LIMIT MINIMUM LIMIT 0.51 [0.020] MIN 10.16 [0.400] TYP.
1 25.75 [1.014] 25.25 [0.994]
14
DIMENSIONS IN MM [INCHES]
28SDIP
28TSOP (TSOP028-P-0813)
0.28 [0.011] 0.12 [0.005] 28 0.55 [0.022] TYP. 15
12.00 [0.472] 11.60 [0.457]
13.70 [0.539] 13.10 [0.516]
12.60 [0.496] 12.20 [0.480]
1 8.20 [0.323] 7.80 [0.307]
14 0.20 [0.008] 0.10 [0.004] 0.15 [0.006] 1.10 [0.043] 0.90 [0.035] 1.20 [0.047] MAX. 0.425 [0.017] 0.20 [0.008] 0.00 [0.000] 0.425 [0.017] 1.10 [0.043] 0.90 [0.035] 0.20 [0.008] 0.00 [0.000]
28TSOP
DETAIL
0 - 10
DIMENSIONS IN MM [INCHES]
MAXIMUM LIMIT MINIMUM LIMIT
10
CMOS 256K (32K x 8) Static RAM
LH52256C/CH
ORDERING INFORMATION
LL - ## X LH52256C X Device Type Operating Package Speed Power Temp
Low-Low-power standby 70 Access Time (ns) Blank 28-pin, 600-mil DIP (DIP028-P-0600) D 28-pin, 300-mil SK-DIP (DIP028-P-0300) N 28-pin, 450-mil SOP (SOP028-P-0450) T 28-pin, 8 x 13 mm2 TSOP (Type I) (TSOP028-P-0813) Blank 0 to +70C H -4 to +85C CMOS 32K x 8 Static RAM
Example: LH52256C-70LL (CMOS 32K x 8 Static RAM, Low-Low-power standby, 70 ns, 28-pin, 600-mil DIP)
52256C-7
11

▲Up To Search▲

Price & Availability of LH52256C

	To Download LH52256C Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .